91蜜桃传媒吹潮粉嫩少妇,久久AV红桃秘 一区二区小说,台湾成人做爰A片,8x8×8Ⅹ成人无码免费视频
Hello! Shenzhen Win-drive Automation Equipment Co., Ltd. welcomes you!
0755-82113520、13823217507(WeChat)Site map|Legal Notice|Chinese
News
News
Current location: Home News Industry news How should the maintenance of the planetary gearbox be done?
How should the maintenance of the planetary gearbox be done?

Industry news|2022-04-07| admin


People often ask how to maintain the planetary gearbox. In fact, the maintenance of the gearbox is relatively simple. The correct installation in the early installation and the subsequent use can be well lubricated and maintained. It can be maintained normally without overloading during operation. operation. Today, I will introduce to you how to maintain the gearbox.




1. The bearing chamber of the planetary gearbox is worn, including the failure of the casing structure, the bearing box, the bearing chamber of the inner hole of the box, and the bearing chamber of the gearbox.




2. The shaft diameter of the planetary gearbox gear is worn, and the main wear parts are the shaft head, keyway, etc.




3. The bearing position of the planetary gearbox drive shaft is worn.




4. The joint surface of the planetary gearbox leaks.




For the main wear problem, the traditional solution of the enterprise is to repair welding after brush plating or machining repair, but there are some drawbacks in these two methods. In order to solve the leakage problem, we usually use traditional methods to disassemble the gearbox, replace the gasket or use the sealant, which is not only time-consuming and labor-intensive, but also difficult to effectively ensure the sealing effect, and information leakage will develop again during operation.




1. The operator of the planetary gear gearbox should be familiar with the internal control structure and function of the gearbox, as well as their operation and maintenance procedures. Before analyzing the operation, please read the operation manual, and operate and maintain according to the requirements of the operation manual.


2. Pay attention to the working time of the planetary gearbox to avoid too long working time, which will cause the machine to heat up and affect the use;



3. Use lubricating oil reasonably, and select the appropriate lubricating oil according to the different power and model of the enterprise. At the same time, we need to check the oil quantity and the tightness of the machine.


4. The inside of the machine needs to be cleaned and adjusted regularly to avoid loose or worn parts.



5. Bearing lubrication For the lubrication of rolling bearings in the gearbox, the commonly used lubricants are lubricating oil and grease. When selecting lubricating oil, factors such as bearing load, speed, temperature, working environment, etc. should be considered. The higher the bearing load, the higher the temperature, and the higher the viscosity of the lubricating oil. When the bearing load is small, the temperature is low, and the rotational speed is high, low-viscosity lubricating oil can be used. Too much or too little oil in the bearing can cause the bearing to overheat. When the bearing speed n=1500r/min, the oil level should be lower. When the peripheral speed of the bearing rotating race is not more than 4-5m/h, it can be lubricated with grease. When lubricating with grease, the amount of grease in the bearing can occupy 1/3-1/2 of the bearing cavity space. For the lubrication of rolling bearings in the gearbox, the lubricating oil in the gearbox oil pool can be directly used, and then the lubricating oil in the gearbox oil pool must be introduced into the bearing.


The operation and maintenance personnel of the planetary gearbox need to analyze and check regularly. The continuous improvement of the early work will determine the occurrence of the later situation, so as to make better use of the gearbox and create more economic benefits.


The above is an introduction to some common problems in the operation of planetary gearbox and related maintenance. Those who need planetary gearbox are welcome to consult Shenzhen Weidong Automation Equipment Co., Ltd.

Tel: 0755-82113520, 13823217507  
E-mail: sales@sz -windrive. com  
URL: m.hebeiseo.com com  
Address: room 406, MaoYuan building, No. 9, Songyuan Road, Guiyuan street, Luohu District, Shenzhen  

WeChat

Links
Shenzhen Win-Drive Automation Equipment Co., Ltd.  ALL RIGHT RESERVED 粵ICP備12016317號
亚洲AV秘 无码一区口真希 | 日韩中文字幕在线观看 | 日本黑人乱偷人妻中文字幕 | 国产丨熟女丨国产熟女视频 | 91精品国产色综合久久久蜜香臀 | 色欲av无码人妻中文字幕 | 国产农村一级特黄妇女A片一 | 日本人做爰毛片免费播 | 中文字幕免费观看 | 波多野结衣教师A片无码 | www 17c com| 揄拍成人国产精品视频 | 国产精品成人免费久久黄AV片 | 国产一级婬片A片AAA樱花 | 黄色在线观看视频 | 欧美成人激情视频 | 少妇对白半推半就高清AV | 特级西西人体444WWw高清大胆 | 夜夜爽妓女8888视频免费观看 | 91精品国产乱码久久久 | 中文字幕av一区二区三区免费看 | 国产精品一级无码免费播放 | 日本不卡视频在线观看 | 少妇搡BBBB搡BBB搡澳门 | 黑丝美女自慰在线观看 | 91福利在线观看 | 少女哔哩哔哩高清播放视频 | 亚洲+变态+欧美+另类+精品 | 日本爆乳一区二区三区 | 无码人妻一区二区三区线花季传媒 | 337P日本大胆噜噜噜 | 黄色视频网站免费观看 | 91无码粉嫩小泬无套在线哈尔滨 | 成人亚洲A片V一区二区三区蜜月 | 国产精品扒开腿做爽爽爽视频 | hongtaoav| 欧美成人在线观看 | 北条麻纪码免费版官方 | 久久时所有精品在这里 | 日韩三级电影久久 | 免费一级a毛一级a看免费视频下载 |